Tips For Installing Left Right LED Headlights
Swapping your vehicle’s stock halogen headlights with LED headlights is very simple. However, if you are not careful you might end up installing them upside down. This can be very dangerous for you and other drivers on the road.
To prevent this from happening make sure that the flat sides of the LED bulb face 3 and 9 o’clock (left and right). Once done, test your headlights to see that their beam pattern is correctly aimed downward.
Features
LED headlights are quickly replacing older bulbs in modern vehicles, and for good reason. These bright lights offer improved visibility and a sleek, modern look. They also consume less energy than halogen and HID bulbs, which helps reduce fuel consumption and environmental impact. However, there Left Right LED Headlight are some things you should know before buying a set of LED headlights.
First, you need to understand how they work. LED headlights use multiple LED chips to produce the light that is projected from the lens. Each chip produces a different illumination angle. The outer ‘HDR matrix’ module produces a wide illumination at forty degrees width by ten degree height, while the inner ‘Performance’ module has a narrower beam with higher intensity. The light distributed by the two modules overlaps in the middle, providing a bright, powerful, homogeneous illumination.
Lastly, LED headlights have a much longer lifespan than halogen and HID bulbs. They typically last for 30,000 hours, which is about 20 years of average usage. Some even come with a warranty that shows how confident the manufacturer is in their product.
These LED headlights are made by Cougar Motor and feature Cree chips. They are plug-and-play and CAN bus ready, which means they work with most cars without issues. They are also waterproof and come with a three-year warranty. They have a high output of 3000 lumens for the high beam and 1900 lumens for the low. They also come with a Heise Connect controller, which allows you to adjust the colors and patterns from your vehicle’s dashboard.
Installation
When it comes to installing these LED headlights, there are certain things you should keep in mind. First of all, you should make sure that the bulbs are installed correctly. This is very important because the wrong positioning of the headlights may cause blinding other drivers on the road. The best way to avoid this problem is to follow the instructions that come with the headlights and do not touch them with your bare hands.
Before starting the installation process, you should turn off the vehicle and remove the key from the ignition. Once you have done this, you should remove the rubber cover from the back of the headlight just behind the halogen bulb. Then, you should unplug the connector from the old halogen bulb. Once you have done this, place the halogen bulb in a safe location and install the new LED bulb. You should also connect the LED ballast wiring. One end should go to the new bulb, and the other should be connected to the existing wiring harness of your vehicle.
Finally, you should make sure truck lights suppliers that the LED headlights are aimed correctly. They should be in a horizontal position with the LED chips facing left and right, not up and down. Otherwise, the headlights will create a pattern that is too bright and may blind other drivers on the road.
Warranty
There are countless headlight bulbs on the market. There are blue chip names like Philips and Sylvania, and there are boutique high-end outfits that specialize solely in LED lights. Many of them work fine, but there are some that have issues. One of the most common problems is water ingress, or moisture collecting inside the light and causing failure. This is often caused by improper installation, or by driving in rain or snow. It may also occur if the bulb is pushed in or pulled out too hard. This is usually not a manufacturing defect and does not affect the warranty.
Other common problems are overheating and shortened lifespan. LEDs typically run much cooler than halogen or HID bulbs, and have built-in fans to keep the heat sink cool. The fan can sometimes fail, or the bulbs can overheat, and this will shorten their lifespan. Most LED bulbs advertise a 30,000 hour working life, which works out to 20 years of normal use.
Please check your local and state laws before installing any aftermarket products. Some vehicles require a special anti-flicker module, and some states have restrictions on the brightness of aftermarket headlights. If you are unsure, it is best to consult an experienced professional. Quake LED is not responsible for any fines that you may receive as a result of installing our products.
Feedback
The headlights in your vehicle are more than just a bulb in a socket. They are a carefully shaped and angled cradle of reflectors that help to focus the light from the bulb into a pattern that illuminates your road, while also not blinding oncoming traffic. LED bulbs don’t emit light from the same spot as incandescent bulbs and if they aren’t aimed correctly, they will create a pattern that throws too much light at your eyes. This can be dangerous and will reduce your visibility on the road.
Unlike an incandescent bulb that takes up to 0.2 seconds to light up, an LED bulb lights up almost immediately as soon as the switch is turned on. This allows drivers in the rear of your vehicle to react more quickly and avoid rear-end collisions.
These bulbs are a great choice for upgrading your car’s headlights. They are easy to install, provide a lot of brightness, and are very durable. They are recommended by the manufacturer for use in high and low beams, but can be used as fog lights as well.
We recommend reading the instructions that come with your LED headlights, as they provide valuable information on how to properly set up and use the headlights. If you have any questions or concerns, please contact us. We are always happy to assist you!
